Skip to main content

Printer Epson FX-890, FX-890A



Téléchargements:

Consommables:

Accessories:
  • C12C814022: 50 Sheet A4 Sheet Feeder
  • C12C824432: Type B Serial Interface 20ma 0K
  • C12C811141: Epson Roll Paper Holder LX-300+II, LQ-580, LQ-680, FX-8, FX-890
  • C12C806382: High Capacity Cut Sheet Feeder (150 Copies) LQ-590, FX-890, FX-890A
  • C12C806372: Epson Standard Cut Sheet Feeder LQ-570+, LQ-870, LX-300+II, LQ-300+II
  • C12C800202: Tractor LQ-870, FX-870, FX-880, FX-890, LQ-5
  • C12C824352: EpsonNet 10 / 100 Base Tx.print serv.5e
  • C12C814011: Guide papier


Parts:


Troubleshooting:
  • Meaning of panel light:
Paper Out
Pause
Tear Off/Bin
Pitch
Font
long series of beeps (5 beeps)
An unknown printer error has occurred. Turn off the printer and leave it off for several minutes; then turn on the printer again. If the error recurs, contact your dealer.

Pause
(no bip)
The print head is overheated. Wait for a few minutes; the printer resumes printing automatically once the print head cools.

Paper Out
Pause
short series of beeps (3 beeps)
A single sheet of paper is not fully ejected. Press the Load/Eject button to eject the sheet.
or
Continuous paper is not fed to the standby position.
Tear off the printed page at the perforation; then press the Load/ Eject button. The printer feeds the paper to the standby position.
or
Paper is jammed in the printer.  Clear the paper jam

Pause
short series of beeps (3 beeps)
The paper release lever is set to the wrong position.
Set the paper release lever to the position for the paper source you want to use.

Paper Out
Pause
short series of beeps (3 beeps)
No paper is loaded in the selected paper source.
Load paper in the printer or select a different paper source; the Paper Out light goes off. Then press the Pause button; the Pause light goes off and the printer starts printing.
or
The paper is not loaded correctly. Remove your paper and reload it correctly

Libellés :

Comments

Post a Comment

Popular posts from this blog

How to fix error B200 on canon Printers

MAJ11/06/17 Error B200 means the printhead voltage or temperature is not normal. The Printhead could be defective.... but first, try these solutions below: Solution 1 : Disconnect the power cable from the printer. Wait 1 hour. Connect the power cable Solution 2 : Check and Clean Head contact pin condition of the carriage unit Check Cable connection especially the carriage FFC Solution 3 : Turn off the power Open the panel Turn on the power Wait for print carriage to start moving to the left. Let it go past half way Before print carriage reaches left hand side shut the cover. Leave the Printer turned on Solution 4 : Unplug the power cable. Open the printer Push the whole print head mechanic to the center While the printer still open, plug the power and turn it ON.  When the printhead still moving and is going to the very LEFT, close the cover.  Wait until its boot up.  Solution 4a: Take out all of the ink cartridges Lift up the gr
217 comments
Read more

How to solve error code 006 with Canon Service Tool V3400

MAJ 25/08/17 The Service Tool V3400 allow to reset the counter of some Canon printers. For the error code 006 , try this : Solution 1: Check your cartridges: an empty cartridge can lead to error 006 Solution 2 : After you avec clicked on "Main", wait a few minutes.  If the error still here, restarts the Service Tool Solution 3 : Close the service tool Disconnect the USB cable from the printer After 10 seconds, plug back the cable to the printer On Windows, click next when appears "New device" Open the service tool
11 comments
Read more

How to solve error B204 on Canon Maxify printers

The error B204 could happen after a cartridge replacement. First of all, when installing, remove the cartridges from the plastic package, but do not drill any plastic membranes, as this will cause this error when placing the cartridge. The error may also appear if you change a completely empty cartridge: when installing a full cartridge, the printer enters a cleaning cycle, but the printhead has not yet received ink from the newly inserted cartridge. Here are some tips to cancel this error B204:: Solution 1: Remove the cartridges Power the printer for 2 minutes Switch on the printer Install the cartrdiges Solution 2: Switch on the printer Unplug  the power cable Open the cover Move the print head carriage manually to the usual place where it goes for the cartridge change (If the printhead carriage is not movable, reconnect and then turn on the printer, then unplug it again when the head carriage is in the moving position). Change the cartridges. Close the fr
2 comments
Read more