Skip to main content

Canon Pixma MP170 Ink Tank Full Error



How to reset error 5B00 for Canon MP170 (Ink Tank Full Error):

1 - power off.
2 - hold stop/reset ,hold ON/OFF
3 - release stop/reset, push stop/reset twice, quickly, then release ON/OFF
4 - wait untill LCD display shows "Canon Idle",then push stop/reset four times, quickly
5 - then push power twice, quickly
6 - power off and power on.

Cartridges:
Parts:

Comments

Splaktar said…
Thanks, that worked for me. The other steps I found online were slightly different and didn't work.
gabrielinri said…
Canon Pixma MP140 series ''INK TANK
FULL ERROR''How to fix it
LEH said…
Hi gabrielinri,


For Canon MP140, try this:
http://fix-your-printer.blogspot.com/2010/11/error-5b00-on-canon-printers-pixma.html

Good luck !
ryan said…
What the hell?! That worked!!! seems so obvious in hindsight. upupdowndownleftrightleftright
Ar-Rumbiwi said…
thaaaannkkksss,,,, helpful...:D
Anonymous said…
First of 5 different solutions I tried that actually worked
Anonymous said…
never goes idle. just back to error 5b00
Anonymous said…
Sorry but mine is a Mx410. I have replaced absorber pad. What a chore. It will reset with these procedures. It just goes back to 5b00 and never goes idle to complete procedure.
Anonymous said…
It worked! :) :) On a Canon MP220, now the only question is, was that a temporary fix? Either way, thank you!!
Anonymous said…
Awesome! Worked on my MP470. Tried 10+ different other methods before this. Had almost given up. THANKS!
Shishir Khedkar said…
Thanks for nice sharing. You can also find latest Printing technology in Splashjet.co.in. Printing technology has witnessed a sea change with the advent of modern printers, latest software and advanced printing methods. For more information Visit inktank

Popular posts from this blog

How to fix error B200 on canon Printers

MAJ11/06/17
Error B200 means the printhead voltage or temperature is not normal. The Printhead could be defective.... but first, try these solutions below:


Solution 1:
Disconnect the power cable from the printer.Wait 1 hour.Connect the power cable
Solution 2:
Check and Clean Head contact pin condition of the carriage unitCheck Cable connection especially the carriage FFC
Solution 3:
Turn off the power Open the panel Turn on the power Wait for print carriage to start moving to the left.Let it go past half way Before print carriage reaches left hand side shut the cover. Leave the Printer turned on
Solution 4:
Unplug the power cable.Open the printerPush the whole print head mechanic to the centerWhile the printer still open, plug the power and turn it ON. When the printhead still moving and is going to the very LEFT, close the cover. Wait until its boot up. 
Solution 4a:
Take out all of the ink cartridgesLift up the grey bar by where the ink goesLeft the print head in the middle of the pr…

Service tool V3400 for resetting Canon printers counter

MAJ 11/06/17 The Service Tool V3400, and service tool V3600, allow you to reset the waste ink pad counter on some Canon printers: 

You can solve the messages errors "Waste Ink Tank Full" or "Waste Ink Pad Full", "error 5B00" or "Error P07" on these printers:
Canon Pixma iP2700, iP4800, iP4810, iP4840, iP4850, iP4900, iP4910, iP4940, iP4970, iP4980, iP4990, iP5810, iP5880 Canon Pixma MP230, MP240; MP250; MP260; MP270; MP280; MP480; MP490; MP540; MP550; MP560; MP620; MP630; MP640; MP980; MP990; Canon Pixma IX6500, IX6510, IX7000 Canon Pixma IP3600, IP4940 Canon Pixma PRO9000, PRO9500 Canon Pixma MG2120. MG2140, MG2240, MG2250, MG2440, MG3240, MG3140, MG4100, MG4140, MG5140, MG5150, MG5240, MG5340, MG6140, MG6240, MG8140, MG8240 Canon MX397, MX320, MX330, MX860 etc
Where can you download the Service Tool V3400 ?

It is free here:
ST V3400. (but check first for no virus or trojan)
There is too a paid version here:
V3400 Canon Service Tool for all iPxx…

Solving error code 2,140,21 or 2140,21 on Canon printers

MAJ 11/06/17
Error 2,140,21 or 2,157,50 appears on Canon printers when the scanner is used.
"Printer is in use or an error has occurred. Check status. Scanner driver will be closed. Code : 2,140,21"

Solution 1:
On Windows: go to "devices"Click on "Printer"Click on "Stop printing".
Solution 2:
Reinstate the driver of the printer.
Solution 3:
Turn off the firewall
Solution 4:
Sometimes, replacing the cartridge could solve the problem.